Clik here to view.
Re: WAN circuit utilization
Here is what I did for this although I'm certain there are multiple ways to tackle. I wrote an alert every time circuit utilization exceeded X% for 30 minutes. Then I wrote an NPM event that gave the...
View ArticleRe: 3750X Health Monitors
I ran into this too.... If your 3750's are wired for redundant power, pull out the P.S. Health monitor is calling out. Wait a few seconds, then push it back in. This has worked several times for me....
View ArticleRe: Is WMI Protocol dangerous?
I would state that WMI is more secure...It requires username/password to access whereas only SNMPv3 requires credentials. SNMP is limited as well as deverts stated only pulling in basic information....
View ArticleRe: Advanced Alerts triggered with SQL and SW STRING variables
Ok, Trying your example: ${SQL:SELECT Value FROM CustomPollerStatusTable INNER JOIN CustomPollers ON CustomPollerStatusTable.PollerID = CustomPollers.CustomPollerID WHERE UniqueName = 'GBAvailable' AND...
View ArticleRe: Customizing the UnDP Summary Chart Bubble
Node status is represented by the icon with some specific color which is determined only based on the ICMP ping. We introduced new feature UnDP on Maps in current release NPM 10.6 which allows you to...
View ArticleClik here to view.
Unknow host LDAP template
Hello, I am facing to a problem with the ldap template config. We have some ldap with the exactly same config. I activated the template for test environment and it's working well. Now I want to do it...
View ArticleRe: Adding additional options to Java/JavaMail
Opposite, actually. I'm connecting to an Exchange 2010 system. It broadcasts AUTH=PLAIN which seems to trigger javamail to try it. It doesn't actually work. Exchange-2010 SMTP AUTH support
View ArticleClik here to view.
Re: Energywise Overall Power Consumption displaying incorrect data
So I think I may have found my answer, unless something written back in 2008 has been changed by now http://thwack.solarwinds.com/thread/22496 According to this thread, Summary charts don't support...
View ArticlePhantom Nodes in NCM
NPM 10.5, NCM 7.2 Just starting a rebuild of NCM (initial build wasn't fully configured). To test configuration backups, config change templates, and all that I put a single switch in NCM as 'licensed...
View ArticleRe: rectifier Status
Sounds like we are pulling table values here. A quick overview of UnDP may be handy: Video Tutorial: Universal Device Poller in Orion NPM - Videos | SolarWinds
View ArticleO.I.D not supported?
I am using the universal device poller.In Define your UnDP I select browse MIB.I got to alpha MIB tree and select >dcpower > dcpersystraps > dcpwrsysalarmactivetrap When i select alpha as my...
View ArticleRe: What does trend 1, 10 and 11 means?
Screenshot would be super helpful on this to make sure we're on the same page.
View ArticleRe: O.I.D not supported?
It basically means that the device you are polling doesn't understand that request it is unsupported on that particular device. Sometimes its a versioning issue on the device or merely an...
View ArticleRe: NPM - SQLExpress
I used to have multiple licenses of NPM when I worked for a managed service provider. Anything under 250 nodes I used the SQL express for. That being said however I was only running NPM no other...
View ArticleRe: Phantom Nodes in NCM
Hi yotaguy, I suggest you do a "Node Sync" in the NCM Manage nodes page. It will likely add these two NCM nodes back into the Orion Platform database and you will then be able to delete them. Hope...
View ArticleRe: We were unable to connect to any of your WWW addresses listed
DNSReport does not accept an IP Address as input; what did you enter into the input field? I checked the domain for the given IP Addess, and the test returned valid results.
View ArticleRe: We were unable to connect to any of your WWW addresses listed
Am I missing something, Manimaran. Which test did you use to get this result.Why would it want to connect on port 80 anyway, the given IP Address is not presumed to be a webhost; it is the primary DNS...
View ArticleTrigger event in Serv-U? Able to make the user see the event?
Hi all, I have a serv-u server and I wish to create an event. I need to be able to see the event running (as it needs input from the user). How do I do this in Serv-U? Thanks Ben
View ArticleRe: 500 thwack point limited time offer: how would you like to use Cron to...
Kellie Mecham this is a great idea to have slight move towards *nix type programmability. These can have so much more robustness and can integrate easily to scripts. I like what adatole has mentioned...
View Article